Es ist immer ein guter Zeitpunkt, um unserem Haus einen neuen Anstrich zu geben und die Veränderungen vorzunehmen, die wir für unser Haus geplant haben. Keramik bietet uns alles, was wir brauchen, um jedem Raum den perfekten Touch zu geben, denn es ist ein Material mit unzähligen Vorteilen: es ist natürlich und recycelbar, es ist ein sicheres Material, da es feuerfest ist und keine giftigen Dämpfe abgibt, es zeichnet sich auch durch seine Widerstandsfähigkeit, Unveränderlichkeit und leichte Reinigung aus, ganz zu schweigen von seiner unendlichen ästhetischen Vielseitigkeit, die uns zahlreiche Möglichkeiten in Bezug auf Oberflächen, Formate, Farben oder Grafiken bietet, die es schaffen, sich an jeden Einrichtungsstil anzupassen.
Wir schlagen eine Reihe von Ideen vor, die bei der Planung einer Wohnungsrenovierung mit Keramikfliesen als Inspiration dienen.
Heutzutage ist eines der grundlegenden Konzepte, die wir bei der Renovierung unseres Hauses befolgen müssen, Räume mit Materialien zu schaffen, die unsere Umwelt respektieren. Keramische Wandfliesen, die zu 100 % aus natürlichen Bestandteilen bestehen, sind eine gute Wahl, wenn wir den Respekt vor der Natur und die Qualität miteinander verbinden wollen, da sie uns helfen, gesunde und effiziente Räume durch vielseitige, widerstandsfähige Oberflächen mit geringen Wartungskosten zu schaffen.
Keramik trägt dazu bei, dass die Beleuchtung, ob natürlich oder künstlich, in unserer Wohnung an Bedeutung gewinnt. Keramische Materialien nutzen die Eigenschaften des Lichts und tragen dazu bei, die scheinbare Größe von Räumen zu verändern, ihnen ein Gefühl von Weite zu verleihen, ihre Schönheit und Attraktivität zu steigern und dank ihrer polierten oder glasierten Oberflächen eine größere Leuchtkraft zu erzielen.
Keramische Wandfliesen mit Reliefs sind ein Beispiel dafür, wie Volumen ein entscheidendes Element sein kann, wenn es darum geht, Empfindungen zu erzeugen. Die visuellen Effekte dieser Art von Keramikstücken sind sehr vielfältig, sie ersetzen Linearität durch Bewegung und evozieren Bilder durch Berührung. Die Kombination dieser Stücke auf glatten Oberflächen schafft Kontraste, die das Interesse des Raumes fokussieren.
Die Farbe hat einen entscheidenden Einfluss auf das Gefühl, das ein Raum vermittelt. Deshalb sollte man sich vor der Wahl einer Farbkombination immer Gedanken über den Stil machen, den man wiedergeben möchte. Die Vielfalt der Farben, Töne und Farbpaletten, die wir in den Keramikkollektionen finden, ermöglicht es uns, jede Farbkomposition zu verwirklichen, so dass sie sich jedem Einrichtungsstil anpasst.
Mit der Wahl der Farbe, der Form oder der Ausführung unserer Fliesen geben wir unserem Zuhause die persönliche Note, die es zu einem einzigartigen Raum macht. Aber diese Personalisierung ist noch nicht alles. Unter den unendlichen ästhetischen Möglichkeiten, die Keramikfliesen bieten, finden wir Fliesen mit Grafiken und Mustern wie: Blumenmotive, Damaste, geometrische Muster, digitale oder orientalische Inspirationen, usw. Alle erdenklichen Grafiken sind mit Keramik möglich und verwandeln unsere Räume in originelle und einzigartige Orte.
Eine der größten Herausforderungen bei der Neugestaltung der Wohnung ist es, das richtige Gleichgewicht zwischen privaten und gemeinschaftlichen Bereichen zu finden. Keramische Fliesen bieten die Möglichkeit, dieses Gleichgewicht zu erreichen. Dank ihrer Vielseitigkeit eignen sich Keramikfliesen für die individuelle Gestaltung aller Arten von Räumen: Küchen, Bäder, Spielzimmer, Schlafzimmer, Ankleidezimmer, Wohn- oder Esszimmer, so dass jedes Familienmitglied seinen bevorzugten Raum hat, in dem es sich am wohlsten fühlt.
The tiles are the kings of the kitchens and bathrooms, and it is rare that the house does not have them in one of these rooms. Its insulating walls and protective function as well as the ability to clean, something we can not do on the paint, makes hits in these places.
Although cleaning is very simple, not always accompany the results. And the passage of time, coupled with factors such as daily fat accumulation often difficult to get them shiny again.
We will learn a few home remedies that will help us to make this task have a good ending. As normal substances have at home such as vinegar or ammonia they will provide us with the task of restoring brightness and total clean our tiles.
Water and vinegar: Pour water and a splash of vinegar (half cup) in a bowl. Stir and with the help of a piece of paper soaked in liquid paper, we cleaned the tiles.
We finish the task by passing a cloth dampened with water to remove any remaining vinegar and smell that could be.
Water and ammonia: Same as above, but substituting vinegar for ammonia. Their results are very similar, we can choose the version you like best.
Should be marked with a punch the site where drilling has tile on it and then cross two pieces of masking tape, so that the bit does not slip.
Make holes on the wall tiling is a task that, while not difficult, can have drawbacks if some minimal precautions are not taken. This article reviews tips drilling tiles and on the importance of using masking tape and drill bits TCT in this work. It also mentions the alternative of a specialized tool: Drill the fastener.
Drilling on tiles is a task without being too difficult, headaches can result if proper precautions are not taken. The main hurdle to face are the features tiled surface: very smooth, hard and brittle. This can make the cost make the hole in the right place, or worse, break the tile, in which case there will be no choice but to replace it. Below, a few tips are given to prevent this from happening.
The first step is to define where you have to make the hole. Joints should be avoided. The closer to the center of the tile, the better, because the central area is the greater resistance offered. If a hole in the coupling of two (or more) tiles, it is likely that at least one crack is performed.
Another precaution to take, not least, has to do with making sure the wall has been no drilling pipes or other internal connections that may be damaged by drilling. To check, you can check the house plans or better yet , use a cable and pipe detector .
Once defined the exact site , should point it out first with a pen and then make a small mark on it with a punch and hammer. Should be very careful when making this sign (very small , barely lift the enamel) , as excessive force could also damage the entire tile. That point will be the guide for the drill tip will not move and the hole is in the desired location .
The next step is to glue two pieces of tape crossed on tile, so that the intersection between the two pieces of tape is just above the gate mark bodybuilder. This material will provide stability and avoid any detours bit once it has begun the task of drilling.
Before you grab the drill, it is advisable to get a paper, folded to form an envelope or "pocket" and paste (you can use the same masking tape) just below where the hole is to be performed. Thus, most of the dust detached from the wall will go there and further facilitate the work of cleaning.
And at the time of taking the drill, you have to take two precautions. The first is to use a bit of a tough material called TCT (colloquial name that is known to tungsten carbide or tungsten , and derived from the German phrase "Wie Diamant", ie, "as diamond"). And second, running the drill in normal mode and not in percussion, as use in the latter could cause the breaking of the tile.
As a recommendation, holes should not be performed on the tiled with a drill bit with a diameter greater than 6 millimeters. In the event that a larger hole is needed, one alternative is to drill with the drill bit first 6 mm and then enlarge the diameter with a greater bit.
There is a tool specifically designed to drill on tiles: the jig drills. Its use is not widespread, but very useful. It is a plastic piece whose shape reminds the barrel of a revolver, with circular holes of different diameters, to suit a variety of sizes of drill bits. At one end, the fastener has a gum which, when pressed against the tile produces a suction effect and attaches it to the wall.
Although the fixative used bits, you still need a punch mark the exact spot where it was drilling. But then no longer need to use the masking tape because the supplies fixing charges.
The most important thing to know about placing tiles is that the wall surface needs to be leveled and rough but uniform.
The premise to place tiles in the bathroom properly is, first, make all measurements the width and height of each wall less the part of the doors and windows; is also recommended to add to the previous result one square meter more material to have a margin of error. Furthermore, it is necessary to adjust the cuffs that are defective tiles to adhere to the surface perfectly.
As a first step the most important thing is to plug all the holes and cracks with cement and sand are much more resistant to humidity typical in places like the bathroom elements. As usually you have to cut some tiles to fit perfectly on the wall, what to do is always start with the most visible part of this space, so that the pieces that have been cut are placed in less visible parts place.
With respect to the height, and depending on where the furniture is located, will begin to place full tiles in the top or at the bottom as best suits, that is, if the furniture is in the bottom the tiles must be integers from above so that will cut into the bottom it will not be visible. When considering how to place tiles must consider the height at which van switches and sockets.
The cement recommended for this purpose since the plastic is to be distributed in each tile facilitates leveling and better adherence of the same. Then with the help of a wooden mallet they are placed each ceramic hitting until it fits snugly. Then a spirit level to make sure it has been properly leveled space where they have been placed.
Knowing how to place tiles also noted that they do not have enamel defects because it will remove harmony with the rest of the wall required. To cut the tiles a cutting machine that, despite being easy to handle, it is advisable to be used by people who already have practical use in management. The process of how to place tiles also requires making holes of water intakes, for which a very sharp tip is used steel and ceramics are glazed part hits.
Knowing how to place tiles also noted that they do not have enamel defects because it will remove harmony with the rest of the wall required. To cut the tiles a cutting machine that, despite being easy to handle, it is advisable to be used by people who already have practical use in management. The process of how to place tiles also requires making holes of water intakes, for which a very sharp tip is used steel and ceramics are glazed part hits.
